Info |
---|
title | To Configure Connection, Controller, and Door Settings |
---|
|
Users can choose EITHER one of the two methods to configure the Connection, Controller, and Door settings. |
.
Info |
---|
|
The XP-M1000i-SE21 controller does not directly support 3rd party readers. Add-on module if 3rd party card reader is required: XP-MK-WG10S |
.
.
.
Step 1: Open xPortalNet Comm Service.
Step 2: Ensure that the xPortalNet Comm Service Status is Running.
Figure 1: xPortalNet Comm Service Running pop-up message
Step 3: Right-click the xPortalNet Comm Service icon at the notification bar, click Check Service Info and verify that the software detects the plugged in USB license key.
Figure 2: Valid software license key detected indication
.
.
Step 1: Assign static IP address for XP-M1000i / XP-M1000i-M1300i SE21 controller via web diagnostic.
.
.
.
Step 2: For Connection setup, open xPortalNet Server > Server Admin > Connection Setup. The Connection Setup window will be shown as below.
Figure 3: Connection Setup window
Step 3: Click Add to add a new connection. The Add Connection window will be shown as below. Click OK to save the changes.
Figure 4: Add Connection window
Step 4: For Controller Setup, go to Server Admin > System Device Setup > Controller. The Controller Setup window will be shown below:
Figure 5: Controller Setup window
Step 5: Click Add to add a new controller. The Add Controller window will be shown as below. Click OK to save the changes.
Figure 6: Add Controller window
Step 6: For Door Setup, the Add Door window will be prompted by xPortalNet software as shown below. Click OK to save the changes.
Figure 7: Add Door window
Info |
---|
|
- TTL In / Out Reader No configuration settings are only applicable when the third party reader is connected directly to the TTL port.
- If users are not using TTL readers, users can ignore the TTL Reader settings.
|
.
.
Step 7: The following message window will be shown to indicate that the Record is Added. Click OK to continue.
Figure 8: Record Added window
Step 8: The Connection, Controller, and Door settings are configured. Users can now observe the controller and door Status at Device List.
.
.
Step 1: To use the controller Search function, go to xPortalNet Server > System Device Setup > Controller > Search.
Figure 9: The Search icon
Step 2: The Controller Discovery window will be shown as below. Once the connected controllers are discovered, select the controller to be configured and click Configure Controller.
Figure 10: Controller Discovery window
Step 3: The Configure Controller window will be shown as below. Users are advised to re-assign the controller's IP address, subnet mask, gateway and Server IP address following the site requirements.
Figure 11: Configure Controller window
Step 4: After clicking OK, xPortalNet software will prompt users to enter the web diagnostic password to proceed to update changed settings.
Figure 12: Software prompting to enter web diagnostic password
Step 5: The following message window will be shown once all settings are updated. Click OK.
Figure 13: Settings are updated successfully! message window
Step 6: The Add Connection window will be shown. Fill up the respective fields. Click OK to continue.
Figure 14: Add Connection window
Step 7: The following message window will be shown to indicate that the Record is Added. Click OK to continue.
Figure 15: Record Added message window
Step 8: The Add Controller window will be shown. Fill up the respective fields. Click OK to continue
Figure 16: Add Controller window
Step 9: The following message window will be shown to indicate that the Record is Added. Click OK to continue.
Figure 17: Record Added message window
Step 10: The Add Door Setting window will then be shown. Fill up the door details as below and click OK.
Figure 18: Add Door window
Info |
---|
|
- TTL In/Out Readers are then connected to the respective TTL ports following the TTL In Reader No. and TTL Out Reader No. settings respectively.
- If users are not using TTL readers, users can ignore the TTL Reader settings.
|
.
.
Step 10: The following window will be shown after users have configured the relevant settings. Please wait until prompt the Request submitted to refresh connection window. Click OK to continue.
Figure 19: Retrieving Controller Information window
Figure 20: Refresh Connection message window
Step 11: The Connection, Controller, and Door settings are configured. Users can now observe the controller and door Status at Device List.
.
.
Step 1: After completing the Connection, Controller and Door settings using EITHER of the two methods, users can now check the status of the controller and door.
Step 2: To check the status of the controller, go to xPortalNet Server > Device List > Controller List to verify that the controller Status is Up.
Figure 21: Controller List under Device List tab
Step 3: To check the status of the door, go to xPortalNet Server > Devices List > Door List to verify that the door Status is Up.
Figure 22: Door List under Device List tab