Versions Compared

Old Version 26

changes.mady.by.user Wan Lin Lee

Saved on

compared with

New Version Current

changes.mady.by.user Wan Lin Lee

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Problem (Issue) Statement:

How to configure lift access control at xPortalNet Server

Description:

A guide to configure lift access control at xPortalNet Server.

Related Software:

  • xPortalNet v1.5.0.122

Related Hardware:

XP-SNETv2 v3.48, MK800E v1.47, XP-SNET-E32R & HID R10 Reader

System Application:

Lift Masking Access System

Symptom and Finding:

NA

Cause:

For first time configuration on xPortalNet software to use for lift access control.

Solution:


Warning
titleWarning!

  • Users are not recommended to run any xPortal software in Windows XP operating system as the system is unstable

  • Users are also advised to stop the xPortal Services before shutting down the Server PC to prevent any missing transaction issues.

.

.

Warning
titleWarning!

The XP-SNET controller will not send fire alarm signal over to the connected XP-SNET-E32R and/or XP-SNET-E248 extension boards if the configuration settings for the XP-SNET controller is not completed.

Complete the configuration settings for XP-SNET controller in order for XP-SNET-E32R and/or XP-SNET-E248 to respond accordingly to fire alarm signals.

.

.

Summary


Step-by-step Guide:

  • Anchor
    1
    1
    To Configure Connection setup:

Step 1: Go to xPortalNet Server > Server Admin > Connection Setup.
Add Connection Window in xPortalNet Server
Figure 1: Add Connection Window



Step 2: Fill up the connection information accordingly.


Step 3: Click OK to save the changes.

.

.

  • Anchor
    2
    2
    To Configure Controller Setup:

Step 1: Go to xPortalNet Server > Server Admin > System Device Setup > Controller.
Add Controller Window
Figure 2: Add Controller Window


Step 2: Fill up the controller information accordingly.


Step 3: Click OK to save the changes.

.

.

  • Anchor
    3
    3
    To Configure Door Setup:

Step 1: Go to xPortalNet Server > Server Admin > System Device Setup > Door.
Add Door Window
Figure 3: Add Door Window



Step 2: Fill up the information accordingly.


Step 3: Click OK to save the changes.

.

.

  • Anchor
    4
    4
    To Configure Lift Panel Setup:

Step 1: Go to xPortalNet Server > Server Admin > System Device Setup > Lift Panel.
Add Lift Window
Figure 4: Add Lift Window





Step 2: Fill up the information accordingly.


Step 3: Click OK to save the changes.

.

.

  • Anchor
    5
    5
    To Configure Floor Relay Setup:

Step 1: Go to xPortalNet Server > Server Admin > System Device Setup > Floor Relay.
Add Floor Relay Window
Figure 5: Add Floor Relay Window



Info
titleNote

The table below shows the relay number scheme to be followed.

 .
.

Step 2: Fill up the information accordingly.


Step 3: Click OK to save the changes. Here is an example of the added floor relay:
Floor Relay Setup Example
Figure 6: Floor Relay Setup Example

Step 5: Continue by creating Floor Zone and Floor Accessibility for the lift at xPortalNet Client :

Info
titleKnowledge Base Link

Users may refer to How to Create Floor Zone and Floor Accessibility at xPortalNet Client to complete the process.


Date Documentation:

6/4/2018 (Rev 1.0)

Status
subtletrue
colourYellow
titleProof-read

.

Section
bordertrue


Column
width100%

Related Articles.

Containing the label ("e32r" OR "address-config") AND "snet" 

Filter by label (Content by label)
showLabelsfalse
max100
showSpacefalse
sorttitle
cqllabel in ( "e32r" , "address-config" ) and label = "snet" and space = "MKB"


.

.

Choices for confluence
_id5d09ba1824c64e0020444d1a