Info |
---|
title | To Configure IP Address: |
---|
|
Users can choose EITHER one of the 3 methods to configure the GT/GTR controller's IP address. |
Warning |
---|
|
Method 3 is only available to xPortal3000 software. |
Step 1: Press and hold the ColdStart button on the controller board.
Step 2: Turn OFF the power supply.
Step 3: Turn ON the power supply.
Step 4: Release the ColdStart button after 3 seconds. The controller will respond with a long beep to indicate that the ColdStart process is in effect.
Info |
---|
|
Users are advised to perform ColdStart operation once for every fresh installation unless advised otherwise. |
Step 1: Open IE browser (Internet Explorer) and type the default IP address in the address box.
Info |
---|
|
Default IP address for GT/GTR controllers: 192.168.1.20 |
Step 2: The Windows Security dialog box will be shown. Enter the User name and Password and click OK to continue.
Info |
---|
|
Default User Name: admin Password: password10 |
Figure 1: The Windows Security Dialog Box
Step 3: Once the login is successful, the following home window will be shown:
Figure 2: The Web Diagnostic Home Window
Step 3: Go to Configuration > Network. The Network Setting window will be shown. Configure the Controller's IP address, Subnet Mask, Gateway and Server PC's IP address settings. Click Save Setting to save the changes made.
Figure 3: The Network Setting Window
Info |
---|
|
Once the settings are saved, the Web Diagnostic is only accessible via the newly changed controller IP address. |
Step 1: The following home screen will be shown at the controller's LCD:
Figure 4: Controller LCD Home Screen
Step 2: To enter Configuration Menu for the first time, press asterisk key (*) and enter the 6-digits default MasterPIN.
Info |
---|
|
Default MasterPIN: 123456 |
Figure 5: Entering default MasterPIN for first time login
Step 3: The following window will then be shown to prompt users to enter a new MasterPIN which will be used for subsequent logins to enter Configuration Menu.
Figure 6: The Change MasterPIN Window
Step 4: Re-enter the same Master Pin and press √ to confirm the new 6-digits MasterPIN.
Figure 7: Re-enter the Same MasterPIN to confirm the MasterPIN
Step 5: The following window will be shown once the new MasterPIN is updated successfully.
Figure 8: The MasterPIN Updated Window
Step 6: Press the asterisk (*) key, followed by the new MasterPIN to enter Configuration Menu. The following Main Menu window will be shown upon entering Configuration Menu.
Figure 9: The Main Menu Window
Step 7: Press 1 for System Menu. Press 7 to access the Network Settings menu. The following window will be shown. Enter the Local IP Address for the controller and press √ to proceed to the next window.
Figure 10: Enter the Local IP Address
Step 8: At the following window, enter the Local Port No for the controller and press √ to proceed to the next window.
Figure 11: Enter the Local Port No
Warning |
---|
|
The Port No. setting here MUST be the same as the setting for the software. Users are advised to use the default port no. |
Step 9: Next, enter the Remote IP Address for Server's PC and press √ to proceed to the next window.
Figure 12: Enter the Remote IP Address (Server PC)
Step 10: The following window will be shown. Enter the Remote Port No. for the Server PC and then, press √ to proceed to the next window.
Figure 13: Enter the Remote Port No (Server PC)
Warning |
---|
|
The Port No. setting here MUST be the same as the setting for the software. Users are advised to use the default port no. |
Step 11: At the following window, enter the Subnet Mask for the network and press √ to proceed to the next window.
Figure 14: Enter the Subnet Mask
Step 12: Enter the Gateway IP for the network at the following window and press √ to proceed to the next window.
Figure 15: Enter the Gateway Setting
Step 13: Once users have completed all the settings, the following window will be shown to prompt users to save all changes Press √ to save all configuration settings. The controller will then auto restart to allow the changes to take effect immediately.
Figure 16: The Save Changes? Window
Info |
---|
|
If users leave the process at any stage, all changes made previously will not be saved and will be lost. To save the network changes, press √ until users reach this window and press √ again to confirm saving the changes. |
Step 1: Login to xPortal3000 Client software and click Device Lookup.
Figure 17: The Device Lookup Icon
Step 2: The Device Discovery window will start searching for connected controller from the network.
Figure 18: The Device Discovery Window Searching for Controllers
Step 3: Select the detected controller and then click Configure Controller to change the controller settings.
Figure 19: Configuring the Detected Controller
Step 4: The following window will then be shown. Assign a new IP address, Subnet Mask, Gateway and Server IP address. Click OK to confirm and save the changes.
Figure 20: The Network Setting Window
Step 5: The window will prompt users to enter the user name and password. Enter the web diagnostic user name and password to proceed.